Name: PR 4104 Universal uni-/bipolar signal transmitter - Fufeng Marine
Price: 280.00 USD
Availability: InStock

Description

Fast < 20 ms response time for measuring signals produced by torque, position, current & acceleration sensors.
User configurable bipolar or unipolar I/O means the 4104 is suitable for nearly any voltage or current conversion.
The excitation source enables measurement of two or three wire transmitters.
The active or passive I/O makes the 4104 perfect for power matching current loops.
Converts narrow bipolar inputs to wide bipolar or unipolar outputs, e.g., ±1 volt input = ±10 volt or 4…20 mA output.
Selectable direct or inverse I/O makes the 4104 suitable for proportional control applications.
The ”V-curve” function outputs 100% – 0 – 100% when a 0 – 100% input signal is present.

The latest analog and digital techniques are used to obtain maximum accuracy and immunity to interference.
The current output can drive up to 800 Ohms, with an adjustable response time of 0.0…60.0 seconds.
Exceptional mA output load stability of < 0.001% of span/100 Ohm.
Meets the NAMUR NE21 recommendations, ensuring high accuracy in harsh EMC environments.
Meets the NAMUR NE43 recommendations, allowing the control system to easily detect a sensor error.
Each unit is tested to a high 2.3 kVAC, 3-port galvanic isolation level.
Excellent signal to noise ratio of > 60 dB.

Very low power consumption means units can be mounted side by side without an air gap – even at 60°C ambient temperature.
Approved for marine applications.
Configuration, monitoring, 2-point process calibration and more are accomplished using PR’s 4500 series of detachable displays.

All programming can be password protected.

Operating temperature	-20°C to +60°C
Storage temperature	-20°C to +85°C
Calibration temperature	20…28°C
Relative humidity	< 95% RH (non-cond.)
Protection degree	IP20
Installation in	Pollution degree 2 & meas. / overvoltage cat. II

Supply
Supply voltage, universal	21.6…253 VAC, 50…60 Hz or 19.2…300 VDC
Max. required power	≤ 2.5 W
Max. power dissipation	≤ 2.5 W
Isolation voltage
Isolation voltage, test / working	2.3 kVAC / 250 VAC
Response time
Response time (0…90%, 100…10%)	< 20 ms
Auxiliary supplies
2-wire loop supply	> 16 V / 20 mA
3-wire loop supply	> 18 V / 20 mA
Loop supply limitation	30 mA
Programming	PR 4500 communication interfaces
Signal / noise ratio	> 60 dB
Cut-off frequency (3 dB)	> 40 Hz
Accuracy	Better than 0.05% of selected range
EMC immunity influence	< ±0.5% of span
Extended EMC immunity: NAMUR NE21, A criterion, burst	< ±1% of span

Current input
Signal range	±23 mA
Programmable measurement ranges	0…20 and 4…20 mA ± 10 and ± 20 mA
Input voltage drop	1.4 V @ 20 mA
Loop error detection, 4…20 mA: Low	< 3.6 mA
Loop error detection, 4…20 mA: High	> 21 mA
Voltage input
Signal range	±12 V
Programmable measurement ranges	0/0.2…1, 0/1…5, 0/2…10 VDC ±1, ±5 and ±10 V
Input resistance	> 2 MΩ

V-curve function, 100-0-100%	20-0-20 mA
External loop supply	3.5 – 26 V
Voltage output
Programmable signal ranges	0/0.2…1; 0/1…5 ; 0/2…10 V ±1, ±5 and ±10 V Direct or Inverted action
V-curve function, 100-0-100%	1-0-1, 5-0-5 and 10-0-10 V
Load (@ voltage output)	≥ 500 kΩ
Response time, programmable	0.0…60.0 s
Output limitation – outside range: on unipolar V signals starting from 0	0 and 115% of max. value
Output limitation – outside range: on unipolar V signals with offset	-5% of min. value and 115% of max. value
Output limitation – outside range: on bipolar V signals	±115% of min. & max. values
Sensor error indication, at 4…20 mA input: selectable	Low, High, Zero, None

PR 4104 Universal uni-/bipolar signal transmitter